Direktori Produk

Filter Pencarian

Negara

Indonesia (9)

USA (1)

Semua Negara (10)

Kategori Keanggotaan

Platinum (4)

Semua Kategori Member (4)

Kategori Perusahaan

Manufacturer (10)

Semua Kategori (10)


Reset pencarian

Produk terkait

  • HOT COIL SPRING
    A hot coil spring is open helical spring that offers resistance to a compressive force applied axially. Hot coiled coil springs can be subjected to elevated temperatures or operate in a corrosive environment. Hot coil springs are made from bars of carbon or alloy steel.
    • Jl. Mayjend Sungkono No.10 Kab. Gresik
    • +62 31 3981135
    • +62 31 3981531
  • TENSION SPRINGS
    Tension Springs are springs which absorb and store energy by offering resistance to a pulling force. Typically, Tension springs are made from round wire and are close wound with initial tension.
    • Jl. Mayjend Sungkono No.10 Kab. Gresik
    • +62 31 3981135
    • +62 31 3981531
  • VALVE SPRINGS
    Valve springs are one of the most critical and most overlooked components in your engine. Proper selection of the valve spring begins with identifying the application and selecting all of the valve train components to achieve the engine builders’ goals.
    • Jl. Mayjend Sungkono No.10 Kab. Gresik
    • +62 31 3981135
    • +62 31 3981531
  • COMPRESSION SPRINGS
    Compression Springs are a type of spring designed to compress and become smaller when presented with compressive load. Compression spring normally refers to a coil compression spring, but there are other types of springs and spring-like objects used as compression springs in special applications.  
    • Jl. Mayjend Sungkono No.10 Kab. Gresik
    • +62 31 3981135
    • +62 31 3981531
    • Taman Permata Indah 2 Blok Z No.108 / 10C Jakarta Utara Kota Administrasi Jakarta Utara
  • BEZINAL® XP COATED WIRE FOR RELIABLE, HIGHLY CORROSION RESISTANT SPRINGS, BEKAERT INDONESIA
    Corrosion is perceived as the primary cause of break-downs, malfunctions and premature failures. Choosing a steel wire with the right corrosion protection is therefore essential for the production of a reliable and durable spring.
    • JL. surya Utama Kav. I-14 Kota Industry Suryacipta Kab. Karawang
    • Taman Permata Indah 2 Blok Z No.108 / 10C Jakarta Utara Kota Administrasi Jakarta Utara
  • TORSION WIRE SPRING
    Torsion springs are used to store rotational energy or to apply torque. It is always best to design these springs to wind up in use and to apply force in the direction of the wind – otherwise unfavorable bending stresses will occur. As a torsion spring deflects in the direction of the wind, the spring’s diameter will decrease and its body length will increase. In these situations it is recommended that the spring be supported on its inner diameter (I.D.) with a shaft or tube, sized so that there will be no binding as the torsion spring deflects.
    Double-torsion springs are a common type of torsion spring. They are made of a left hand component and a right hand component which are connected at the center. It is possible to have the two components connect at the outside edge, though this is not recommended.
    Most springs are wound with the coils touching but with minimal initial tension. For these springs the body length can be calculated by multiplying the wire diameter by the number of coils, then adding one.
    • 5408 Panola Industrial Blvd Decatur
    • Taman Permata Indah 2 Blok Z No.108 / 10C Jakarta Utara Kota Administrasi Jakarta Utara