Direktori Produk

Filter Pencarian

Negara

Indonesia (35)

USA (31)

Semua Negara (66)

Kategori Keanggotaan

Platinum (1)

Free (23)

Semua Kategori Member (24)

Kategori Perusahaan

Manufacturer (44)

Distributor (1)

Supplier (10)

Contractor (11)

Semua Kategori (66)


Reset pencarian

Produk terkait

  • KAWAT BRONJONG SNI
    Dear Customer. CV. DUA PUTRA PETIR MENJUAL KAWAT BRONJONG PABRIKASI / KAWAT BRONJONG MESIN , KAWAT BRONJONG SNI , KAWAT BRONJONG MANUAL .

    KEGUNAAN KAWAT BRONJONG :
    - PENCEGAHAN EROSI PADA TANGGUL SUNGAI
    - PELINDUNG KELUARAN GORONG-GORONG
    - PELINDUNG PENYANGGA JEMBATAN
    - PERLINDUNGAN GARIS PANTAI

    MENYEDIAKAN
    - BRONJONG SNI 03-0090-1999 YANG PRODUKSI MESIN ( BRONJONG PABRIKASI)
    - BRONJONG KAWAT MANUAL
    - BRONJONG PVC SNI 03-3046-1992 ( PVC COATED GABION )
    - GEOTEXTILE 150 GR , GEOTEXTILE 200 GR , GEOTEXTILE 250 GR , GEOTEXTILE 300 GR
    - WIRE NETTING DENGAN LEBAR 1 METER SAMPAI 4 METER DENGAN PANJANG 50 M SAMPAI 150 M
    - SACK GABION DENGAN PANJANG MULAI 2 METER SAMPAI 4 METER DENGAN DIAMETER MULAI DARI 0.45 METER SAMPAI 0.85 METER

    HARGA KAWAT BRONJONG ( HARGA GABION ) PER 17 PEBRUARI 2014 :
    - 2 X 1 X 0.5 ( 2.7 MM) : RP 195.000 ( PRODUKSI MESIN)
    - 2 X 1 X 0.5 ( 2.7 MM) : RP 155.000 ( PRODUKSI MANUAL)
    - 2 x 1 x 1 ( 2.7 MM) : RP 285.000 ( PRODUKSI MESIN)
    - 2 X 1 X 1 ( 2.7 MM) : RP 240.000 ( PRODUKSI MANUAL)
    - 2 x 1 x 0.5 ( 3 MM) : RP 245.000 ( PRODUKSI MESIN )

    HARGA BRONJONG MURAH MULAI DARI HARGA RP 85.000

    BERIKUT INI INFORMASI HARGA BRONJONG PVC PER TANGGAL 24 OKTOBER 2012 :
    - PVC 2 X 1 X 0.5 ( 2.7 MM) : RP 330.000 ( PRODUKSI MESIN )
    - PVC 2 X 1 X 1 ( 2.7 MM) : RP 520.000 ( PRODUKSI MESIN ) CV.DUA PUTRA PETIR Bukit Palma C5/33 Citraland Utara – Surabaya Telp. 03188000026/27 Telp . 03317406677 / 7407380 Fax : 031-7417127 Email: duaputrapetir@gmail.com Website : www.besisurabaya.com  www.duaputrapetir.co.id   www.duaputrapetir.indonetwork.co.id , www.jualpolycarbonate.indonetwork.co.id  www.jualbesisurabaya.indonetwork.co.id www.besibetonsnisurabaya.blogspot.com www.besikanal.blogspot.com  www.tandonairpenguin.blogspot.com  www.tandonairmurah.blogspot.com www.duaputrapetir.blogspot.com
    • Bukit Palma C5/33 Kota Surabaya
    • +62 31 7406677
    • +62 31 7417127
  • RS / RSS PUSH-PULL-PROPS (PERI PRODUCTS)
    Push-Pull-Props used as a buffer in the manufacture of the panel to reach a height of 14.00 meters. Advantages For formwork-heights up to 14.00 m Fast and easy to connect to the formwork panel Easy fixing of the base plates Adjustable Kicker Brace
    • Jl. Penjernihan No.40 Kota Adm. Jakarta Pusat
  • ACS SELF CLIMBING SYSTEM
    Advantages Crane Independence Crane independent forming, striking and climbing speeds up the work prodedures on the project site and also makes independent from each other. This allows a constant cycle and keeps the operation in a rhythm. Therefore the crane can be used for other necessary tasks. Climbing during all weather conditions PERI ACS can be climbed during all weather conditions. The comfortable platforms allow safe and efficient working routines like on the ground. To provide weather protection the working platforms can be enclosed. High load capacity and safety standard The working platforms are able to carry high loads. For example the storage of reinforcing steel for the next climbing lift. Even the placing boom for the concrete pump can climb on the ACS units if required. Wide and stable working platforms, the well designed structure which resists the highest wind loads and the patented cam and pawl indexing system are just parts of the extensive safety precautions. Modular system components The 3 variations ACS-R (Regular), ACS-P (Platform) and ACS-G (Gallows) can work next to each other on the same building or even be combined to mixed units. Through custom-made enhancements the best possible solution will be found even for the most complicated building structure.
    • Jl. Penjernihan No.40 Kota Adm. Jakarta Pusat
  • RORO HEAVY DUTY SHORING S40
    Robust, heavy duty shoring with normal scaffolding couplers to make trusses or trestles with variable bases. Advantages Insensitive to settlement Insensitive to the small wind surface Insensitive to central load introduction to a ball socket in the base Available in tested column load types
    • Jl. Penjernihan No.40 Kota Adm. Jakarta Pusat
  • SKS SINGLE SIDED CLIMBING SYSTEM
    Designed for safety on high structures. Advantages The stable and economic climbing bracket for heavy duty uses Wide bracket spacing enables to plan big-sized formwork panels with optimized exploitation of the load capacity. This means cost-effective solutions. Safe and cost-effective anchorage The screw anchor M30/530 is especially designed for single-sided formwork on SKS/SSC within dam construction. The screw anchor M30/530 is used to transfer large tension forces and shear forces into green, non-reinforced concrete. It is completely re-usable and the cost-effective alternative when used frequently on site. Simple and flexible to plan Even round concrete structures can be planned, schedulded and poured with single-sided wallform quick and easily. Inclined concrete surfaces can be poured without special measurements even if vertical concrete loads have to be supported.
    • Jl. Penjernihan No.40 Kota Adm. Jakarta Pusat
  • TUNNEL LINING EQUIPMENT
    Blind-end tunnel excavation technologies using mills or shields. Advantages CIFA Provides Pre-cast Lining Production System The new blind-end tunnel excavation technologies using mills or shields require the section excavated to be supported with precast concrete rings. The special metal forms designed for the production of these rings require machine tool work on the entire surface in contact with the concrete, and special dismantling joints. CIFA supplies the entire precast lining production system, with integrated automation of mixing, transport and laying of the concrete in forms, together with handling and steam curing of the linings.
    • Jl. Penjernihan No.40 Kota Adm. Jakarta Pusat
  • TABLE MODULES
    Completely pre-assembled tableform for hire. Advantages Fully pre-assembled in four standard sizes The PERI table modules are fully pre-assembled tableforms in four standard sizes for optimized adaption to the building: Table module VT 200/215 x 400. Table module VT 250/265 x 400. Table module VT 200/215 x 500. Table module VT 250/265 x 500. Two folding directions for the props. The props are folded in two directions in order to negotiate parapets or downstand beams. Compact transportation storage PERI table module's overall height of 430 mm minimises storage and transportation capacity. Table module can be used as a slab edge tableform. PERI table modules can also be cantilevered at the edge of the slab.
    • Jl. Penjernihan No.40 Kota Adm. Jakarta Pusat
  • UNIPORTAL TABLEFORMS
    Tableform UNIPORTAL is System PERI using Table in manufacture Slab its. Advantages High stability The main girders are spaced 500 mm. Therefore longer girder spans are possible and the stability of the tableform is very high. Foldable props The fixed clamped props are foldable in one direction. Therefore you can negotiate parapets or downstand beams. Customized tableforms Even trapezium-shaped tables with radial girder arrangements are possible. Higher load capacity The props are fixed clamped in the UNIPORTAL head. Therfore you have higher allowable prop loads.
    • Jl. Penjernihan No.40 Kota Adm. Jakarta Pusat
  • PERI GRV CIRCULAR FORMWORK
    Tie-less circular formwork with articulated walling Advantages The tie-less formwork system for circular structures When used in a closed ring PERI GRV functions without any ties Whether large or small radii. The savings achieved in this way are considerable. Cost-effective custom solutions for arched bridges with GRV PERI GRV articulated waler is always the most economical solution for circular, segmental, compound and other arch shapes Continuously adjustable to any radius The patented joints of the PERI GRV waler allow even smallest pin pitch circle radii down to 0.60.
    • Jl. Penjernihan No.40 Kota Adm. Jakarta Pusat
  • HANDSET PANEL WALL FORMWORK (PERI PRODUCTS)
    The Panelized Formwork System. Advantages Small number of panel sizes Just 3 Elementheights and -widths ensures high utilisation for each component. Light elements with carrying handles Thanks to their lightness and ergonomic carrying handles, HANDSET Panel Wall Formwork panels can be shifted easily by hand. One connector - The HANDSET Panel Wall Formwork clip. It not only connects everything and fixes accessories, but also, whether inserted from the left or right, will always resist vibration. Practical arrangement of tie points. This avoids the need to drill additional tie holes, and allows the panels to be offset without additional components.
    • Jl. Penjernihan No.40 Kota Adm. Jakarta Pusat